收藏本站
MPLAB ? REAL ICE ? In-Circuit Emulator User’s Guide
11.5
SETTINGS DIALOG
Select either Debugger>Settings or Programmer>Settings to open the Settings dialog
and set up the MPLAB REAL ICE in-circuit emulator.
Note:
Tabs displayed will depend on the selected device.
?
?
?
?
?
?
?
?
Settings Dialog, Program Memory Tab
Settings Dialog, Configuration Tab
Settings Dialog, Trace Tab
Settings Dialog, Freeze on Halt Tab
Settings Dialog, Status Tab
Settings Dialog, Clock Tab
Settings Dialog, Secure Segment Tab
Settings Dialog, Warnings Tab
11.5.1
Settings Dialog, Program Memory Tab
This tab allows you to set up debug/programming options.
? Allow MPLAB REAL ICE to select memories and ranges – the emulator uses your
selected device and default settings to determine what to program.
? Manually select memories and ranges – you select the type and range of memory
to program.
TABLE 11-8:
Memories
Program
Configuration
EEPROM
ID
MANUAL SELECTION OPTIONS
Check to program Program Memory into target.
Check to program Configuration bits into target.
Note: This memory is always programmed when emulator
selected as a debugger.
Check to erase and then program EEPROM memory on target, if
available. Uncheck to erase EEPROM memory on target.
Check to program ID Memory into target.
Program Options
Erase all before Program Check to erase all memory before programming begins.
Unless programming new or already erased devices, it is important
to have this box checked. If not checked, the device is not erased
and program code will be merged with the code already in the
device.
Program Memory
Start, End
The starting and ending hex address range in program memory for
programming, reading, or verification.
If you receive a programming error due to an incorrect end
address, you need to perform a reconnect, correct the end address
and program again.
Note: The address range does not apply to the Erase function.
The Erase function will erase all data on the device.
? Set up automatic options – choose to “Program after successful build” and/or
“Run after successful program”.
DS51616B-page 108
? 2008 Microchip Technology Inc.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AC244006 KIT MPLAB REAL ICE TRACE
AC2626M6 PROBE TEMP 6" GENERAL PURP
AC300024 MOTOR STEPPER 2PHASE 8WIRE
AC300030 KIT ACOUSTIC ACCESSORY
ACM-16 CABLE MODULE FR3 16BIT 40-DIP
ACM-2X8 ACTIVE CABLE MODULE DUAL 8 BIT
ACM-8 CABLE MODULE FR3 8BIT 28/32-DIP
ACS9510EVB EVALUATION BOARD FOR ACS9510
相关代理商/技术参数
AC244005-2 功能描述:处理器配件 MPLAB REAL ICE w/ Performace Pak RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
AC244006 功能描述:仿真器/模拟器 MPLAB REAL ICE TRACE INTERFACE Brd KIT RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
AC244007 制造商:Microchip Technology Inc 功能描述:MPLAB REAL ICE JTAG ADAPTER - Boxed Product (Development Kits) 制造商:Microchip Technology Inc 功能描述:ADAPTER MPLAB REAL ICE JTA 制造商:Microchip Technology Inc 功能描述:ADAPTER, MPLAB, REAL, ICE, JTAG 制造商:Microchip Technology Inc 功能描述:ADAPTER, MPLAB, REAL, ICE, JTAG; Accessory Type:JTAG adaptor Board; For Use With:Microchip PIC32MX devices; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes
AC244008 功能描述:处理器配件 MPLAB REAL ICE Power Monitor RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
AC244022 功能描述:插座和适配器 Procs Extnsn Pak for PIC24FJ128GA010-ICE RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244022 制造商:Microchip Technology Inc 功能描述:Processor Extension Pak for PI
AC244023 功能描述:插座和适配器 PROCESSOR EXTNSN PAK FOR PIC18F1xK50 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244024 功能描述:插座和适配器 Processor Ext Pak for PIC18LF14K50 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x